We continue to work!
The next order of eddy current flaw detectors will be shipped to Mexico by the end of May..

Eddycon Purpose

eddy current flaw detector Eddycon is referred to the testing and evaluation means.It is intended for manual testing by eddy current technique for the presence of surface and subsurface defects, such as discontinuity of the material (cracks, overlaps, holes, fine cracks, etc.)


    testing of aeronautical engineering parts (wheel disks, covering, turbine blades, multilayered constructions, holes of various kinds etc.);
    testing of pipelines, turbine blades of gas-distributing station (GDS), pressure vessels, etc.;
    testing of pipelines, industrial vessels etc.;
    testing of steam generator pipes by inner bobbin eddy current probes ,( I/D ECP), collectors etc.;
    testing of rods, wire, metalwares, forming rolls, sheet metals, metal parts of bearing structures etc.,

Eddycon eddy current flaw  detector


  • Possibility of tuning out from the influence of operating liftoff of testing object electromagnetic properties inhomogeneity;
  • Storage of a great number of setups and testing results in the flaw detector memory;
  • Special-purpose software;
  • Mode of two-way connection with PC via USB port (for inputting the information from the flaw detector memory into PC and possibility of this data printing as well as setups loading from PC into the flaw detector memory);
  • Possibility of conditional defect depth and length evaluation;
  • Sound and color ALARM system.
  • Operation simplicity due to the intuitive interface;
  • Pluggable battery;

    Pluggable battery

  • Small mass and dimensions parameters.
  • Device complies with European standard 61326: 2005 (First edition).

Flaw detector distinctive features:

  • Color high-contrast TFT display;
  • ALARM system: 4 three-color LEDs, sound alarm; various scanning units manipulation;
  • possibility of operation in two-frequency mode;
  • simplified procedure of instrument calibration on calibration blocks;
  • possibility of encoder and eddy current rotary scanner connection;
  • possibility of rapid measurement of the ratio signal/noise;
  • USB slave;
  • possibility of low-temperature instrument version (minus 30 °С).


  • The possibility of defects detection – from 0,1 mm and opening – from 0,002mm;
  • operating frequency setup range – from 50 Hz to 12 МHz;
  • generator output voltage (double amplitude) – from 0,5 V to 16 V;
  • adjusted gain range - 30 dB;
  • adjusted preamplifier range- 40 dB;
  • signal phase change (range of signal rotation from 0 to 360 with a step of 0,1, 1, 10);
  • samples frequency–up to 8 kHz;
  • digital signal filtering (there are 5 filter types: Lowpass, Highpass, Bandpass, Differential, Averaging);
  • eddy current signal display: a) complex plane (XY) – allows to detect defects among interferences by analyzing the signal waveform; b) generation of two channel maturing, can be used for suppression of interfering factors and reduction of their influence on testing results(for mixing an operator can choose one of 5 algorithms: addition, subtraction, addition with horizontal inversion, addition with vertical inversion and multiplication).
Eddy current signal display
Eddy current signal display
  • two modes of instrument operation: day mode - is used when operating in dimly lit places with insufficient visibility; night mode - is used when operating in places with bright lighting, to increase the display contrast;
  • time of flaw detector operation mode setup – up to 1 minute;
  • autozap function(adjustable time of screen clearing in 0.1 s and 0.5 s, 1 s, 2 s, 3, 4);
  • built-in clock and calendar;
  • screen backlight and screen brightness control;
  • congestion control of input channel;
  • storage battery discharge level indication;
  • possibility of connection and operation of ECP of the following types:
    • differential ECP;
    • differential ECP connected according to the bridge scheme;
    • differential transformer ECP with grounded centerpoint;
    • differential ECP of transformer type;
    • absolute(parametric) ECP;
    • absolute ECP of transformer type;
  • possibility of eddy current rotary scanner connection for the testing of openings and special-purpose scanners;
  • user-friendly multi-language interface;
  • time of continuous flaw detector operation with the fully charged storage battery – at least 5,5 hours;
  • total average life at least 10 years;
  • flaw detector is powered from the built-in storage battery with rated voltage 12 V and rated capacity of 2700 mA * h;
  • weight of flaw detector with a storage battery - no more than 0.8 kg;
  • overall dimensions of flaw detector - no more than 188 mm x107 mm x 78 mm.


Testing of bolt holes with the help of eddy current rotary scanner.

Signal projection (view) from a natural defect such as a crack with depth of 0.56 mm in the aircraft wheel bolt-hole.

Circular scan allows an operator to place the defect in the hole.
Testing of various purpose pipelines

Signals of stress-corrosion defect are obtained by flaw detector Eddycon from the main gas pipeline section through the layer of insulation covering thickness of 6 mm.

Application of flaw detector Eddycon for conduction of main or confirmatory body testing will enable to evaluate the pipe damage level and its further operability.


Application of flaw detector Eddycon for conduction of main or confirmatory body testing will enable to evaluate the pipe damage level and its further operability.

Программное  обеспечение

Main advantages of program application are:

  • An intuitive interface;
  • Convenient view of testing results by each frequency channel (frequency № 1, frequency№ 2 mix.);
  • Possibility of creation and storing of electronic records.
  • Data output on the detected defect, namely:
    • Coordinate position of the defect in the defectogramm;
    • Amplitude and phase of the signal;
    • Flaw depth.

Formed electronic report contains all basic data of conducted testing, namely:

  • Information about the organization, NDT division and an operator who conducted the testing.
  • denomination of the testing object;
  • all flaw detector setups at the inspection moment;
  • signal parameters from the defect (amplitude, phase,flaw depth);
  • flaw signal in the complex plane and on the string diagramms;
  • the date of testing

By agreement with the Customer there is a possibility to create other forms of reports.

Frequency range kHz from 0,5 to 6000
Gain dB 70
Probe supply voltage В 0,5, 1, 2, 4, 8
Sampling frequency Hz 8000
Filter Hz Lowpass from 1 tо 5000;
Highpass from 1 tо 5000;
Bandpass filter;
Connected ECP differential and absolute ECP;
Digital zoom from 1/16 to 16, with a step of 6
Phase rotation °, degr. from 0 to 360
ECP connector 2 - pin LEMO, 4 - pin LEMO
Signal trace time sec. 0,1; 0,5; 1; 2; 3; 4
Display Color LCD
Screen resolution pixel 320 ´ 240
Screen size Inch
2,756 ´ 1,969
70 ´ 50
Signal display modes Complex plane – X(y);
Time scan – X(t), Y(t);
Vector – A(t);
Circular scan – X(y)+A;
Defect alarm (alarm) Frame:
Memory for setups and testing results storage 1 Gb of memory.
1 defectogram occupies – 6 Мb;
1 setup occupies – 0,00355 Мb
Multi-frequency operation 2 – frequency multiplexing;
Independent control of both frequencies;
Signals mix for unwanted effects rejection
Battery Storage battery Hi-MH 12В/2700 mА×h
Operation time from the battery hour. at least 8
Operating temperatures °С from -30 to +40
Protection from environmental impact IP 65 according to GOST 14254
Overall dimensions mm 188 ´107 ´ 78
Weight with storage battery kg no more than 0,8


Sizes of working
1 PN – 05-MDF01 Æ4 500-2000 Æ13×35 Surface defects in different conduction materials (e.g.
aluminum alloys, ferromagnetic
and austenitic steel).
2 PN – 06-MDF01 Æ5 500-1500 Æ13×35
3 PN – 07-MDF01 Æ6 300-600 Æ13×35
4 PN –08-MDF01 Æ7 200-400 Æ13×35 Surface and subsurface cracks, voids, corrosion damages in aluminum alloys , ferromagnetic and austenitic etc.
5 PN – 09- MDF01** Æ8 250-400 Æ13×35
6 PN – 12 -MDF01** Æ12 100-250 Æ13×35
7 PN – 15-MDF01 Æ13 Æ13×38
8 PN – 15-MDF02 Æ13 10-100 Æ15×50
9 PN – 17 -MDF01 Æ15 Æ15×50
10 PN – 05- MDF01 Æ31 1-50 Æ17×50 Surface and subsurface cracks, voids in aluminum alloys and austenitic steel etc.
11 PN-6 ×8 – TD01 6×8 900-1700 Æ31×50 Surface cracks, voids in ferromagnetic steel.
It is used for grooves testing.
12 PN-05- TD 01 Æ3 400-600 Æ12.5×130 Surface cracks, voids, corrosion damages in aluminum alloys, ferromagnetic and austenitic steel etc.
13 PN-05-TD 02 Æ3 750-1100 Æ12.5×70
14 PN-05-TD 04 Æ4 100-450 Æ15×170
15 PN-08-TD 01 C Æ7 Æ35×150 Special ECP for the testing of VR2-26 gear pinions of NI-26 helicopters.
PNR - 03×(5-6)*-TD01 Æ Detection of surface defects in aluminum alloys, ferromagnetic and austenitic steel etc.
They are intended for the testing of holes of different diameters.
They are used a part of the eddy current rotary scanner.
18 PNR-03×(8.5-9.5)*-TDO1 Æ3 2000-3000 Æ
PNR-03×(17-18)*-TD01 Æ
  • View Delivery set of Eddycon portable eddy-current flaw detector